Simple test

Ensure your device works with this simple test.

examples/mpr121_simpletest.py
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
# Simple test of the MPR121 capacitive touch sensor library.
# Will print out a message when any of the 12 capacitive touch inputs of the
# board are touched.  Open the serial REPL after running to see the output.
# Author: Tony DiCola
import time
import board
import busio
# Import MPR121 module.
import adafruit_mpr121

# Create I2C bus.
i2c = busio.I2C(board.SCL, board.SDA)

# Create MPR121 class.
mpr121 = adafruit_mpr121.MPR121(i2c)
# Note you can optionally change the address of the device:
#mpr121 = adafruit_mpr121.MPR121(i2c, address=0x91)

# Loop forever testing each input and printing when they're touched.
while True:
    # Loop through all 12 inputs (0-11).
    for i in range(12):
        # Call is_touched and pass it then number of the input.  If it's touched
        # it will return True, otherwise it will return False.
        if mpr121[i].value:
            print('Input {} touched!'.format(i))
    time.sleep(0.25)  # Small delay to keep from spamming output messages.
examples/piano.py
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
# MPR121 piano demo.
# Listens to the first 7 inputs of the MPR121 and plays a middle scale note
# when an input is touched.  Note only one note is played at a time!
# For use with microcontrollers or computers with PWM support only!
# Author: Tony DiCola
# Modified by: Carter Nelson

import board
import busio
import pulseio

# Import MPR121 module.
import adafruit_mpr121


# Configure PWM buzzer and other state:
BUZZER_PIN = board.D9
TONE_ON_DUTY = 2**15   # Duty cycle of tone when turned on, a square wave.
TONE_OFF_DUTY = 0      # Duty cycle of tone when turned off, 0 or no signal.
NOTE_FREQS = [261,  # Input 0 = 261 hz = middle C
              294,  # Input 1 = middle D
              329,  # Input 2 = middle E
              349,  # Input 3 = middle F
              392,  # Input 4 = middle G
              440,  # Input 5 = middle A
              493,  # Input 6 = middle B
              0,    # Input 7 = nothing (set to a frequency in hertz!)
              0,    # Input 8
              0,    # Input 9
              0,    # Input 10
              0]    # Input 11


# Create I2C bus.
i2c = busio.I2C(board.SCL, board.SDA)

# Create MPR121 class.
mpr121 = adafruit_mpr121.MPR121(i2c)
# Note you can optionally change the address of the device:
#mpr121 = adafruit_mpr121.MPR121(i2c, address=0x91)

# Setup buzzer PWM output.
buzzer = pulseio.PWMOut(BUZZER_PIN, duty_cycle=TONE_OFF_DUTY, frequency=440,
                        variable_frequency=True)

last_note = None
while True:
    # Get touched state for all pins
    touched = mpr121.touched_pins
    # If no pins are touched, be quiet
    if True not in touched:
        last_note = None
        buzzer.duty_cycle = TONE_OFF_DUTY
        continue
    # Get index of touched pin
    note = touched.index(True)
    # Play note if pin is different and has a defined note
    if note != last_note and NOTE_FREQS[note] != 0:
        last_note = note
        buzzer.frequency = NOTE_FREQS[note]
        buzzer.duty_cycle = TONE_ON_DUTY